FM Appendix A Machine Gun Employmentsmall machine

A.      The leader always announces the estimated range to the target. The range is given, so the gunner knows how r to look for the target and what range setting to put on the rear sight. Range is announced in meters. However, since the meter is the standard unit of range measurement, the word meters is not used. With machine guns, the range is determined and announced to the nearest hundred or thousand for example, THREE HUNDRED, or ONE THOUSAND.

A.      The machine guns seldom accompany the maneuver element. The guns primary mission is to provide covering fire. The machine guns are only employed with the maneuver element when the area or zone of action assigned to the assault or company is too narrow to permit proper control of the guns. The machine guns are then moved with the unit and readied to employ on order from the leader and in the direction needing the supporting fire.

A.   Automatic riflemen use assault fire when in close combat. Assault fire involves firing without the aid of sights using the hip, shoulder, and underarm positions. The underarm position is best when rapid movement is required. In all three positions, automatic riflemen adjust their fire by observing the tracer and the impact of the bullets in the target area. Additional considerations for automatic riflemen using assault fire include

A.   When two or more gunners are engaging linear targets, linear targets with depth, or deep targets, they do not engage these targets as they would when visibility is good. With limited visibility, the center and flanks of these targets may not be clearly defined. Therefore, each gunner observes his tracers and covers what he believes to be the entire target.

A.      When machine guns move with the element undertaking the assault, the maneuver element brings the machine guns to provide additional firepower. These weapons are fired from a bipod, in an assault mode, from the hip, or from the underarm position. They target enemy automatic weapons anywhere on the units objective. Once the enemys automatic weapons have been destroyed if there are any, the gunners distribute their fire over their assigned zone or sector. In terms of engagement ranges, the machine gun in the assault engages within meters of its target and frequently at pointblank ranges.

A.   When a pair of gunners engage an enemy target, each gunner is normally responsible for effectively covering one half of the target. The gunners must be prepared to engage the entire target should the other gun go down.

Machine guns should be sited so the maximum number of targets can be engaged, continuous fire can be delivered, and the most likely routes of approach are covered.

Rate of Fire.When gunners engage a target, they initially fire at the rate necessary to gain and maintain fire superiority.

A.      Fire commands do not need not be complete to be effective. In combat, the leader gives only the elements necessary to place fire on a target quickly and without confusion. During training, however, he should use all of the elements to get gunners in the habit of thinking and reacting properly when a target is to be engaged. After the gunners initial training in fire commands, he should be taught to react to abbreviated fire commands, using one of the following methods.

M .mm Armor Piercing.For use against lightlyarmored targets.

A.   This is the space between the muzzle of the weapon and the target where the trajectory does not rise above . meters the average of a standing Soldier that includes the beaten zone. Gunners should consider the danger space of their weapons when planning overhead fires.

A.   Distributed fire is delivered in width and depth such as at an enemy formation. Concentrated fire is delivered at a point target such as an automatic weapon or an enemy fighting position.

Figure A. Application of gunners rule.

Senior squad leader within the platoon. Responsible for all training and employment of the machine guns. The WSLs knowledge, experience, and tactical proficiency influence the effectiveness of the squad.

A.   This section is designed to illustrate the characteristics of machine gun fire, the s of enemy targets that might be engaged, and how to successfully apply machine gun fire on those enemy targets.

A.   Fires with respect to the weapon include fixed, traversing, searching, traversing and searching, swinging traverse, and free gun fires Figure A.

Maintaining alignment with the rest of the assault element.

A.      Initial fire commands are given to adjust onto the target, change the rate of fire after a fire mission is in progress, interrupt fire, or terminate the alert.

Note the point where the new line of aim strikes the ground.

A.   The gunners or leaders knowledge of the machine gun is not complete until he learns about the action and effect of the projectiles when fired. The following definitions will help the leader, gunner, and automatic rifleman understand the characteristics of fire for the platoons machine guns.

WSL or GTL identifies target within gun teams sector

A.   The U.S. Army classifies automatic weapons fires with respect to the ground, target, and weapon.

A.   The gunner ensures throughout his firing that the center of the beaten zone is maintained at the center base of the target for maximum effect from each burst of fire. When this is done, projectiles in the upper half of the cone of fire will pass through the target if it has , and the projectiles in the lower half of the beaten zone may ricochet into the target Figure A.

A.   A good FPL covers the maximum area with grazing fire. Grazing fire can be obtained over various s of terrain out to a maximum of meters. To obtain the maximum extent of grazing fire over level or uniformly sloping terrain, the gunner sets the rear sight at meters. He then selects a point on the ground that he estimates to be meters from the machine gun, and he aims, fires, and adjusts on that point. To prevent enemy soldiers from crawling under grazing fire, he searches downward by lowering the muzzle of the weapon.

A.      The leader must make an estimate of the total amount of ammunition needed to support all the machine guns. He must then adjust the amount of ammunition used for each event to ensure enough ammunition is available for all phases of the operation. Examples of planning rates of fire and ammunition requirements for a platoons machine guns in the attack follow.

WSL identifies sector of fire for gun teams

A.    A sector of fire is an area to be covered by fire that is assigned to an inidual, a weapon, or a unit. Gunners are normally assigned a primary and a secondary sector of fire.

If the gunner is hit by fire, AG/GTL immediately assumes the roll of the gunner.

A.      Adjustments in direction and elevation with the machine gun are always given in meters; one finger is used to indicate meter and so on. Adjustment for direction is given first. For example RIGHT ONE ZERO METERS or LEFT FIVE METERS. Adjustment for elevation is given next. For example ADD FIVE METERS or DROP ONE FIVE METERS. These changes may be given orally or with armandhand signals.

M .mm Ball.M ball ammunition can be fired with the M, but accuracy is degraded. It should therefore only be used in emergency situations when M ball is not available.

A.   In many situations, the leader must issue orders directly to inidual Soldiers. Personal contact is used more than any other method by Inntry leaders. The leader must use maximum cover and concealment to keep from disclosing the position or himself.

A.   Trajectory is the curved path of the projectile in its flight from the muzzle of the weapon to its impact. The major ctors that influence trajectory are the velocity of the round, gravity, rotation of the round, and resistance of the air. As the range to the target increases, so does the curve of trajectory Figure A.

Gun prepare for barrel change.

Shift Fire.Gunners shift their fires without command when more dangerous targets appear.

Figure A. MB machine gun, bipod and tripod mounted.

Defines the sector limits by laying the gun for direction along one sector limit and by emplacing a stake along the outer edge of the folded bipod legs. Rotates the legs slightly on the receiver, so the gunner takes up the play. Uses the same procedure for placing a stake along the opposite sector limit.

A.   Line of sight is an imaginary line drawn from the firers eye through the sights to the point of aim.

A.      The SBF position, not the assault element, is responsible for ensuring there is no masking of fires. The assault element might have to mask the SBF line because they have no choice on how to move. It is the SBF gunners job to continually shift fires, or move gun teams or the weapons squad to support the assault and prevent any masking.

A.      These guns provide sustained direct fires that cover the most likely enemy mounted avenue of approach. Their maximum effective range enables them to engage enemy vehicles and equipment at r greater ranges than the platoons other direct fire weapons.

Lays the machine gun along the FPL by moving the muzzle of the machine gun to a sector limit. Adjusts for elevation by driving a stake into the ground so the top of the stake is under the gas cylinder extension. This allows a few mils of depression to cover irregularities in the terrain.

Slower rate to conserve ammunition sustained rate while still preventing effective return fire as the assault moves forward.

Appendix F Obstacle Reduction and Employment

Lay the gun on the target with the correct sight setting to hit the target.

AG/GTL calls the ammunition bearer if ammunition is needed or actively seeks it out if the ammunition bearer is not available. Constantly updates the WSL on the round count and serviceability of the MB.

A.      Leaders must take into account the SDZ of the machine guns when planning and executing the lift and or shift of the SBF guns. The effectiveness of the enemy on the objective will play a large role in how much risk should be taken with respect to the lifting or shifting of fires.

A.   Gunners have difficulty detecting and identifying targets during limited visibility. The leaders ability to control the fires of his weapons is also reduced; therefore, he may instruct the gunners to fire without command when targets present themselves.

A.      The platoons defense centers on its machine guns. The platoon leader sites the rifle squad to protect the machine guns against the assault of a dismounted enemy formation. The machine gun provides the necessary range and volume of fire to cover the squad front in the defense.

A.      The MK is not organic to the weapons company, not the Inntry platoon, but because there are many times when Inntrymen use it, it is described in this appendix. The MK supports the Soldier in both the offense and defense. It gives the unit the capability of laying down a heavy volume of close, accurate, and continuous fire Figure A. The MK can also

Once on TGT engage.Gunner looks for laser and identifies target.

A.   Plunging fire occurs when there is little or no danger space from the muzzle of the weapon to the beaten zone. It occurs when weapons fire at long range, when firing from high ground to low ground, when firing into abruptly rising ground, or when firing across uneven terrain, resulting in a loss of grazing fire at any point along the trajectory Figure A.

Repeats command. Ceases all fire onto the objective. Maintains overwatch and scans objective until told to reengage or go out of action.

A.   Any fold or depression in the ground that prevents a target from being engaged from a fixed position is termeddead space. Paragraph A discusses methods of determining dead space.

A.      Successful offensive operations result from the employment of fire and movement. Each is essential and greatly depends upon the other. Without the support of covering fires, maneuvering in the presence of enemy fire can result in disastrous losses. Covering fires, especially those that provide fire superiority, allow maneuvering in the offense. However, fire superiority alone rarely wins battles. The primary objective of the offense is to advance, occupy, and hold the enemy position.

Section I Considerations for Employing and Controlling Fire

Figure A. Classes of fire with respect to the gun.

Changes in the rate of fire are given orally or by armandhand signals.

A.      Inntry platoons will normally have an organic weapons squad that consists of a weapons squad leader and two gun teams. Depending on the units organization or the platoons mission, there could be additional machine gun teams attached or organic to the platoon.

M .Caliber AP.For use against armored aircraft and lightlyarmored vehicles, concrete shelters, and other bulletresisting targets.

If second in the gun teams chain of command, he is always fully capable of taking the GTL position.

Without disturbing the lay of the gun, set the rear sight at a range of , meters.

A.    The gunner uses the notchedstake or treecrotch technique with the bipod mount to engage predetermined targets within a sector or to define sector limits. This technique is effective during all conditions of visibility and requires little additional material. The gunner uses the following steps

A.   The gunners rule can be applied when the friendly troops are at least meters in front of the gun position and the range to the target is meters or less Figure A. The rule follows

A.   Using a bipodmounted machine gun, the gunner places a log or board beneath the stock of the weapon so the stock can slide across it freely. He digs shallow, curved trenches or grooves for the bipod feet to allow rotation of the feet as he moves the stock along the log or board. The gunner may mark the sector limits by notching or placing stops on the log or board. The gunner uses the bipod firing position and grip.

A.      Machine guns are suppressive fire weapons used to suppress known and suspected enemy positions. Therefore, gunners cannot be allowed to empty all of their ammunition into one bunker simply because that is all they can identify at the time.

Gun , sustained ‗‗ seconds, engage.

A.   To be effective, machine gun fire must be distributed over the entire target area. Improper distribution of fire results in gaps that allow the enemy to escape or use their weapons against friendly positions without effective opposition.

Classification of Fires With Respect to the Target

A.    The mission is to impose maximum attrition upon the attacking enemy such as lowflying, lowperformance aircraft. Employment of machine guns used for air defense is guided by the following defense design ctors

A.    A final protective fire FPF is an immediatelyavailable, prearranged barrier of fire to stop enemy movement across defensive lines or areas.

A.   Gunners should engage targets only when they can identify the targets, unless ordered to do otherwise. For example, if one gunner detects a target and engages it, the other gunner observes the area fired upon and adds his fire only if he can identify the target or if ordered to fire.

A.   This class of fire is a combination in which successive changes in directionandelevation result in the distribution of fires both in width and depth. It is employed against a target whose long axis is oblique to the direction of fire.

Repeats Gun Tripod and lays down tripod if not done and prepares to lock gun on tripod.

A.   Refer to DA PAM for a more detailed discussion of the SDZs for machine guns.

Mutual Support.When two or more gunners are engaging the same target and one stops firing, the other increases the rate of fire and covers the entire target. When only one gunner is required to engage a target and the leader has alerted two or more, the gunner not firing aims on the target and follows the movements of the target. He does this to fire instantly in case the other machine gun malfunctions or ceases fire before the target has been eliminated.

A.      Machine gun fire has different effects on enemy targets depending on the of ammunition used, the range to target, and the nature of the target. It is important that gunners and leaders understand the technical aspects of the different ammunition available to ensure the machine guns and automatic weapons are employed in accordance with their capabilities. Machine guns and automatic weapons use several different s of standard military ammunition. Soldiers should use only authorized ammunition that is manuctured to U.S. and NATO specifications.

A.      Despite their postCivil War development, modern machine guns did not exhibit their full potential in battle until World War I. Although the machine gun has changed, the role of the machine gun and machine gunner has not. The mission of machine guns in battle is to deliver fires when and where the leader wants them in both the offense and defense. Machine guns rarely, if ever, have independent missions. Instead, they provide their unit with accurate, heavy fires to accomplish the mission.

A.      When fire is to be withheld so surprise fire can be delivered on a target or to ensure that both gunners open fire at the same time, the leader may prece the command to commence firing with AT MY COMMAND or AT MY SIGNAL. When the gunners are ready to engage the target, they report READY to the leader. The leader then gives the command FIRE at the specific time desired. If immediate fire is required, the command FIRE is given without pause and the gunners fire as soon as they are ready.

A.   The M . caliber machine gun is not organic to the Inntry platoon, but as there are many times when Inntrymen use it, it is described in this appendix Figure A.

M .Caliber Incendiary.For incendiary effect, especially against aircraft.

Interrupt or Cease Firing.The leader raises his arm and hand palm outward in front of his forehead and brings it downward sharply.

A.      Battlefield noise and the distance between the gunner and the leader often make it necessary to use armandhand signals to control fire Figure A. When an action or movement is to be executed by only one of the gunners, a preliminary signal is given to that gunner only. The following are commonly used signals for fire control

A.   The cone of fire is the pattern formed by the different trajectories in each burst as they travel downrange. Vibration of the weapon and variations in ammunition and atmospheric conditions all contribute to the trajectories that make up the cone of fire Figure A.

A.   Tracer ammunition helps a gunner engage targets during limited visibility and should be used if possible. It is important to note that in certain circumstances the enemy will have an easy time identifying the machine guns position if the gunner uses tracer ammunition. The need to effectively engage targets must be balanced with the need to keep the guns safe before deciding to employ tracers. If firing unaided, gunners must be trained to fire low at first and adjust upward. This overcomes the tendency to fire high.

A.      Under certain terrain conditions, and for proper control, machine guns may join the maneuver or assault unit. When this is the case, they are assigned a cover fire zone or sector.

A.   Frontal fire occurs when the long axis of the beaten zone is at a right angle to the front of the target. This of fire is highly desirable when engaging a column formation. It then becomes enfilade fire as the beaten zone coincides with the long axis of the target Figures A and A. Frontal fire is not as desirable when engaging a line formation because the majority of the beaten zone normally lls below or after the enemy target.

Still not finding what youre looking for? Drop a comment on a post or contact us so we can take care of it!

Figure A. M machine gun, bipod and tripod mounted.

To terminate the alert, the leader announces CEASE FIRE, END OF MISSION.

Observation.The gunners continuously observe their sectors.

A.   Suce danger zones SDZs were developed for each weapon and are defined as the area in front, back, or side of the muzzle of the weapon that provides a danger to friendly forces when the weapon is fired. The SDZ is not just the area that comprises the cone of fire as it moves downrange. It also involves the possible impact area on both sides of the gun target line and the possible dispersion of material caused by the strike of the rounds, the possible ricochet area, and any area to the rear that is adversely affected by the effects of firing the weapon Figure A.

Table A. Example weapons squad equipment by position.

A.   Read the appropriate FM as shown in Table A for more weaponspecific information on engaging enemy targets with a particular machine gun.

*****Gunners always carry enough CLP for hours of operations.

Lift and shift to targets of opportunity.

Gun out of action, prepare to move.

A.      These guns are not as accurate when mounted on vehicles as they are when fired from the tripodmounted system. They are, however, more easily maneuvered to alternate firing locations should the need arise.

A.    When laying the machine gun for predetermined targets, the gunner can use field expedients as a means of engaging targets when other sources are not available.

**x magnifier, flares, and shift signals are readily accessible at all times.

Barrel change every minute RPM in continuous burst

Primary responsibility is to the gun. Focused on its cleanliness and proper function. Immediately reports any abnormalities to the GTL or WSL.

Once identified, Sector/target identified.

Repeats rate of fire and maintains proper count, telling gunner when to fire. Adjusts rate of fire off of lead gun.

A.      It is essential that the commands delivered by the weapons squad leader are understood and echoed by the assistant gunner/gun team leader and the gunner. Table A provides an example of the weapons squad fire commands and actions used by the weapons squad leader WSL, assistant gunner AG/gun team leader GTL, and gunner.

M mm HE.Comes packed in a round container. It has a wound radius of meters, but lacks the armor piercing capabilities of the HEDP round. It arms to meters from the muzzle.

Provide indirect fires from defilade positions.

A.   Rapid rate of fire places an exceptionally high volume of fire on an enemy position. Machine gunners normally engage targets at the rapid rate to suppress the enemy quickly. Rapid fire requires much more ammunition than sustained fire and requires frequent barrel changes.

A.      Leaders and gunners must know how much ammunition is required to support the different rates of fire each platoon machine gun and assault weapon will require. Coupling this knowledge with an accurate estimate of the length of time and rates of fire their guns are scheduled to fire will ensure enough ammunition resources to cover the entire mission. As part of an example of the planning needed to use MBs in supportbyfire roles, the rates of fire for the MB are listed in Table A.

A.      The weapon squad leader positions and controls the fires of all machine guns in the element. Machine gun targets include key enemy weapons or groups of enemy targets either on the objective or attempting to reinforce or counterattack. In terms of engagement ranges, machine guns in the baseoffire element may find themselves firing at targets within a range of meters. The nature of the terrain, desire to achieve some standoff, and the other ctors of METTTC prompt the leader to the correct tactical positioning of the baseoffire element.

GTL is responsible for his team members and all the gun equipment.

A.   To fire the cyclic rate, the gunner holds the trigger to the rear while the assistant gunner feeds ammunition into the weapon. This is normally only used to engage aerial targets in selfdefense or to fire the final protective fire in the defense to protect the perimeter. This produces the highest volume of fire the machine gun can fire, but can permanently damage the machine gun and barrel and should be used only in case of emergency.

Figure A. Classes of fire with respect to the ground.

Classification of Fires With Respect to the Ground

Drives either a notched stake or tree crotch into the ground where selected targets are anticipated. Places the stock of the machine gun in the nest of the stake or crotch and adjusts the weapon to hit the selected targets and to define his sector limits.

A.   Gunners need to know several terms associated with predetermined fire.

Section II Weapon and Munition Characteristics

A.      The leader may want to place the fire of one machine gun on an enemy machine gun and quickly tells the gunner to fire on that gun.

Look through the sights and notice where the new line of aim strikes the ground. This is the limit of troop safety. When the feet of the friendly troops reach this point, fire must be lifted or shifted.

Lightskinned truck, oclock, m, on my laser.

Section VI Close Air Support and Naval Gunfire

A.      Leaders must know the technical characteristics of their assigned weapon systems and associated ammunition to maximize their killing and suppressive fires while minimizing the risk to friendly forces. Table A lists machine gun specifications and technical data. Read the FMs specific to the machine guns listed in Table A for complete information regarding their technical specifications.

Using binoculars identifies sectors and states, Gun identifies. Adjusts gunner onto target.

A.      Available MK machine gun ammunition is classified as follows Table A.

Responsible for the tripod and TE mechanism. They must always be clean and ready for combat. Responsible for replacing them, if necessary.

A.   Predetermined fires organize the battlefield for the gunners. They allow the leader and gunner to select potential targets or target areas that will most likely be engaged or that have tactical significance. This includes dismounted enemy avenues of approach, likely positions for automatic weapons, and probable enemy assault positions. The gunners do this by using sectors of fire, final protective lines, or a principal direction of fire and selected target areas. This preparation maximizes the effectiveness of the machine gun during good as well as limited visibility. It enhances fire control by reducing the time required to identify targets, determine range, and manipulate the weapon onto the target. Abbreviated fire commands and previouslyrecorded data enable the gunner to aim or adjust fire on the target quickly and accurately. Selected targets should be fired on in daylight whenever practical to confirm data. The range card identifies the targets and provides a record of firing data.

Nightmarks with PEQ/tracerGun , left, center, right sectors on my mark. Do you identify?

A.A correct sight picture has the target, front sight post, and rear sight aligned. The sight picture has sight alignment and placement of the aiming point on the target. The gunner aligns the front sight post in the center of the rear sight and then aligns the sights with the target.The top of the front sight post is aligned on the center base of the target.

A.      Machine gun fire is distributed in width and depth in a defensive position. The leader can use machine guns to subject the enemy to increasingly devastating fire from the initial phases of his attack, and to neutralize any partial successes the enemy might attain by delivering intense fires in support of counterattacks. The machine guns tremendous firepower enables the unit to hold ground. This is what makes them the backbone or framework of the defense.

Watch and shoot or Traverse and search

A.      The leader orally gives the direction to the target in relation to the position of the gunner for example, FRONT, LEFT FRONT, RIGHT FRONT.

Lightskinned truck, oclock, m, on my laser.

A.   Searching distributes fires in depth by successive changes in elevation. It is employed against a deep target or a target that has depth and minimal width, requiring changes in only the elevation of the gun. The amount of elevation change depends upon the range and slope of the ground.

Digs shallow, curved trenches or grooves for the bipod feet. These trenches allow for rotation of the bipod feet as the gunner moves the stock from one crotch or stake to another.

A.      In the offense, Ms target any enemysupporting weapons being fired from fixed positions anywhere on the squads objective. When the enemys supporting weapons have been destroyed, or if there are none, the machine gunners distribute their fire over that portion of the objective that corresponds to their teams position.

A.      The MK is normally vehicle mounted on a pedestal, ring, or weapon platform, but can also be fired from the M tripod. It fires high explosive HE and high explosive, dual purpose HEDP rounds. The HE round is effective against unarmored vehicles and personnel.

Talking the gun teams ensuring one gun fires during the other guns interval and visa versa.

A.      When the gunner is in doubt about any element of the fire command, he replies, SAY AGAIN RANGE, TARGET. The leader then announces THE COMMAND WAS, repeats the element in question, and continues with the fire command.

Determine the range to this point by the most accurate means available.

A.   The beaten zone is the elliptical pattern formed when the rounds within the cone of fire strike the ground or target. The and shape of the beaten zone change as a function of the range to and slope of the target, but is normally oval or cigar shaped and the density of the rounds decreases toward the edges. Gunners and automatic riflemen should engage targets to take maximum effect of the beaten zone. The st way to do this is to aim at the center base of the target. Most rounds will not ll over the target, and any that ll short will create ricochets into the target Figure A.

A.      A mounted platoon might have access to enough machine gun ammunition to support the guns throughout any operation. A dismounted platoon with limited resupply capabilities has to plan for only the basic load to be available. In either case, leaders must take into account key events the guns must support during the mission. They must plan for the rate of machine gun fire needed to support the key events, and the amount of ammunition needed for the scheduled rates of fire.

During firing, pulls rear security and if the gunner comes under enemy fire, provides immediate suppression while the gun moves into new position.

AG/GTL continuously links rounds and gives WSL round count every . Gun , rounds.

Figure A. Example suce danger zone for machine guns.

A.   The machine gun can provide units with a selfdefense capability against hostile lowflying, lowperformance aircraft. These guns are employed in the air defense role as part of the units local defense. The machine guns are not components of an integrated and coordinated air defense system. Unless otherwise directed, hostile aircraft within range of the gun about meters maximum effective range should be engaged. The decision will be made by the commander. Typical targets are surveillance, reconnaissance, and liaison aircraft; troop carriers; helicopters; and drones.

A.      When mounted on the tripod, the M and MK are highly accurate to their maximum effective range and predetermined fires can be planned for likely high pay off targets. The trade off is these weapon systems are relatively heavy, and take more time to move.

A.The extent of grazing fire and the extent of dead space may be determined in two ways. In the preferred method, the machine gun is adjusted for elevation and direction. A member of the squad then walks along the FPL while the gunner aims through the sights. In places where the Soldiers waist midsection lls below the gunners point of aim, dead space exists. Armandhand signals must be used to control the Soldier who is walking and to obtain an accurate account of the dead space and its location. Another method is to observe the flight of tracer ammunition from a position behind and to the flank of the weapon.

Figure A. March column with four machine guns.

A.   A principal direction of fire PDF is assigned to a gunner to cover an area that has good fields of fire or has a likely dismounted avenue of approach. It also provides mutual support to an adjacent unit. Machine guns are sighted using the PDF if an FPL has not been assigned. If a PDF is assigned and other targets are not being engaged, machine guns remain on the PDF. A PDF has the following characteristics

A.      The potential of air and any potential ground attacks on the unit demands every possible precaution for maximum security while on the move. Where this situation exists, the machine gun crew must be thoroughly trained in the hasty delivery of antiaircraft fire and of counterfires against enemy ground forces. The distribution of the machine guns in the formation is critical. The machine gun crew is constantly on the alert, particularly at halts, ready to deliver fire as soon as possible. If the leader expects a halt to exceed a brief period, he carefully chooses machine gun positions to avoid unduly tiring the machine gun crew. If he expects the halt to extend for a long period, he can have the machine gun crew take up positions in support of the unit. The crew covers the direction from which he expects enemy activity as well as the direction from which the unit came. The leader selects positions that permit the delivery of fire in the most probable direction of enemy attack, such as valleys, draws, ridges, and spurs. He chooses positions that offer obstructed fire from any potential enemy locations.

Select a point on the ground where it is believed friendly troops can advance with safety.

Echoes command, starts count. Tells gunner to fire. Keeps count between bursts and ensures gun does not fire out of turn.

A.    The secondary sector of fire is assigned to the gun team to cover the second most likely avenue of enemy approach. It is fired from the same gun position as the primary sector of fire.

Inntry Soldiers tackle urban operations training

n         If it strikes at the selected point, that point marks the limit of safety.

Whether organic to the unit or attached, machine guns provide the heavy volume of close and continuous fire needed to achieve fire superiority. They are the Inntry platoons most effective weapons against a dismounted enemy force. These formidable weapons can engage enemy targets beyond the capability of inidual weapons with controlled and accurate fire. This appendix addresses the capabilities, limitations, and fundamental techniques of fire common to machine guns.

A.   Because of dispersion, only that part of the beaten zone in which percent of the rounds ll is considered the effective beaten zone.

M .Caliber API.For combined armorpiercing and incendiary effect.

Figure A. Classes of fire with respect to the target.

Normally the newest member of the gun team. Must quickly learn everything he can, exert maximum effort at all times, and attempt to outdo his gun team members in every situation.

Figure A. Line of aim and placement of center of beaten zone on target.

Gunner engages target with correct rate of fire.TGT identified.

Aiming low and adjusting the aim upward toward the target.

A.   The method of applying fire to a target is generally the same for either a single gun or a pair of guns. Direct lay is pointing the gun for direction and elevation so the sights are aligned directly on the target. Fire is delivered in width, depth, or in a combination of the two. To distribute fire properly, gunners must know where to aim, how to adjust their fire, and the direction to manipulate the gun. The gunner must aim, fire, and adjust on a certain point of the target. Binoculars may be used by the leader to cilitate fire adjustment.

It is used only if an FPL is not assigned; it then becomes the machine guns part of the units final protective fires.

A.   Predetermined targets, including the FPL or PDF, are engaged on order or by SOP. The signal for calling for these fires is normally stated in the defense order. Control these predetermined targets by using armandhand signals, voice commands, or pyrotechnic devices. Gunners fire the FPL or PDF at the sustained rate of fire unless the situation calls for a higher rate. When engaging other predetermined targets, the sustained rate of fire is also used unless a different rate is ordered.

A.   The available M . caliber machine gun ammunition is classified as follows Table A.

WSL gives gun teams the rate of fire. As long as they are keeping correct interval, they should talk themselves.

GTL leads by example in all areas. He sets the example in all things.

*WSL and AG/GTL load tracer rounds mix in magazines for marking targets.

A.      Machine gun fire from a supportbyfire SBF position must be the minimum possible to keep the enemy from returning effective fire. Ammunition must be conserved so the guns do not run out of ammunition.

The gunner is responsible for the entire wedgeshaped area from the muzzle of the weapon to the target, but elevation may be fixed for a priority portion of the target.

A.    These actions depend upon visual means. The sites selected for the guns must provide maximum observation and unobstructed sectors of fire. Units furnished machine guns in sufficient numbers should site them within mutual support distances of to meters. Each gun is assigned a primary and secondary sector of fire. Weapon crews maintain constant vigilance in their primary sectors of fire, regardless of the sector in which the guns are actually engaged.

A.      In the defense, the medium machine gun provides sustained direct fires that cover the most likely or most dangerous enemy dismounted avenues of approach. It also protects friendly units against the enemys dismounted close assault. The platoon leader positions his machine guns to concentrate fires in locations where he wants to inflict the most damage to the enemy. He also places them where they can take advantage of grazing enfilade fires, standoff or maximum engagement range, and best observation of the target area. Machine guns provide overlapping and interlocking fires with adjacent units and cover tactical and protective obstacles with traversing or searching fires. When final protective fires are called for, machine guns aided by M fires place an effective barrier of fixed, direct fire across the platoon front. Leaders position machine guns to

A.      Once the SBF line is masked by the assault element, fires are shifted and or lifted to prevent enemy withdrawal or reinforcement.

Distributing fires across the objective when not engaging enemy automatic weapons.

Gunner takes gun off tripod, continues to orient towards target on bipod, and prepares to move.

Gun out of action, prepare to move.

A.    An FPL is a predetermined line along which grazing fire is placed to stop an enemy assault. If an FPL is assigned, the machine gun is sighted along it except when other targets are being engaged. An FPL becomes the machine guns part of the units final protective fires. An FPL is fixed in direction and elevation. However, a small shift for search must be employed to prevent the enemy from crawling under the FPL and to compensate for irregularities in the terrain or the sinking of the tripod legs into soft soil during firing. Fire must be delivered during all conditions of visibility.

A.      In the defense, MK and M machine guns may be fired from the vehicle mount or dismounted from the vehicle and mounted on a tripod at a defensive fighting position designed for the weapon system.

A.   The gunner must move his beaten zone in a certain direction over the target. The direction depends on the of target and whether the target is engaged with a pair of guns or a single gun. When engaging targets other than point targets with a pair of guns, the targets are ided so fire is evenly distributed throughout the target area. Fire delivered on point targets or a specific area of other target configurations is called concentrated fire.

A.   Traversing disperses fires in width by successive changes in direction, but not elevation. It is delivered against a wide target with minimal depth. When engaging a wide target requiring traversing fire, the gunner should select successive aiming points throughout the target area. These aiming points should be close enough together to ensure adequate target coverage. However, they do not need to be so close that they waste ammunition by concentrating a heavy volume of fire in a small area.

GTL enforces field discipline while the gun team is employed.

A.      The MK and M can be used as part of the baseoffire element to assist the friendly assault element by suppressing enemy bunkers and lightlyarmored vehicles. Even if ammunition fired from the guns is not powerful enough to destroy enemy vehicles, wellaimed suppressive fire can keep the enemy buttoned up and unable to place effective fire on friendly assault elements. The MK and M are particularly effective in preventing lightlyarmored enemy vehicles from escaping or reinforcing. Both vehicle mounted weapons can fire from a long range standoff position, or be moved forward with the assault element.

A.      The M machine gun is organic to the Inntry platoon and provides rifle squads with a light automatic weapon for employment during assault Figure A. The M can also be used in the machine gun role in the defense or supportbyfire position. The M fires from the bipod, the hip, or from the underarm position. The hip and underarm positions are normally used for closein fire during an assault when the M gunner is on the move and does not have time to set the gun in the bipod position. It is best used when a high rate of fire is needed immediately. Accuracy of fire is decreased when firing from either the hip or shoulder.

M .mm Ball.For use against light materials and personnel.

Lays the machine gun to engage other targets within a sector limit. Done in a primary sector by using the procedure described previously, except he keeps the elevation fixed.

A.   The oral fire control method can be effective, but sometimes the leader may be too r away from the gunner, or the noise of the battle may make it impossible for him to hear. The primary means of the oral fire control method is the issuance of a fire command.

A.      Shift and shut down the weapon squad gun teams one at a time, not all at once. M and mortar or other indirect fire can be used to suppress while the machine guns are moved to where they can shoot.

n         If it strikes short of the selected point, it is safe for troops to advance to the point where the line of aim strikes the ground and to an unknown point beyond. If fire is called for after friendly troops advance rther than the point where the line of aim strikes the ground, this rther point is determined by testing new selected points until the line of aim and the selected point coincide.

A.   When a single gunner is assigned any target he is responsible for covering the entire target.

A.      Fire commands for all directfire weapons follow a pattern that includes similar elements. There are six elements in the fire command for the machine gun alert; direction; description; range; method of fire; and command to open fire. The gunners repeat each element of fire command as it is given.

M .Caliber API Tracer.For combined armorpiercing and incendiary effect, with the additional tracer feature.

Section III Engaging the Enemy without Endangering Friendly Troops

A.   Prearranged signals are either visual or sound signals such as casualtyproducing devices rifle or claymore, pyrotechnics, whistle blasts, or tracers. These signals should be included in SOPs. If the leader wants to shift fire at a certain time, he gives a prearranged signal such as smoke or pyrotechnics. Upon seeing the signal, the gunner shifts his fire to a prearranged point.

A.   Gunners can use overhead fire when there is sufficient low ground between the machine gun and the target area for the maneuver of friendly forces. A machine gun on a tripod is capable of delivering this of fire because of the small and uniform dispersion of the cone of fire. Gunners must accurately estimate range to the target and eslish a safety limit that is an imaginary line parallel to the target where fire would cause casualties to friendly Soldiers. Gun crews and leaders must be aware of this safety limit. Leaders must designate signals for lifting or shifting fires. Gunners should not attempt overhead fires if the terrain is level or slopes uniformly, if the barrel is badly worn, or if visibility is poor.

Oldest barrel parallel strips        Second newest barrel strip       Newest barrelno tape

Return Fire.The gunners return enemy fire without order, concentrating on enemy automatic weapons.

A.    A base stake is used to define sector limits and may provide the lay for the FPL or predetermined targets along a primary or secondary sector limit. This technique is effective in all visibility conditions. The gunner uses the following steps

A.   Application of fire consists of the methods the gunner uses to effectively cover an enemy target area. Training these methods of applying fire can be accomplished only after the weapons squad leader and the gunners have learned how to recognize the different s of targets they may find in combat. They must also know how to distribute and concentrate their fire, and how to maintain the proper rate of fire. Normally, the gunner is exposed to two s of targets in the squad or platoon sector enemy soldiers, and supporting automatic weapons. Leaders must ensure that these targets have priority and that they are engaged immediately.

A.      The leader designates a small or obscure target by pointing with his finger or aiming with a weapon. When he points with his finger, a Soldier standing behind him should be able to look over his shoulder and sight along his arm and index finger to locate the target. When aiming his weapon at a target, a Soldier looking through the sights should be able to see the target. Leaders may also use lasers in conjunction with night vision devices to designate a target to the gunner.

A.   Fires with respect to the ground include grazing and plunging fire.

Repeats command to gunner, ensures gunner lifts fire.

A.   Armandhand signals are an effective fire control method when the gunner can see the leader. All gunners must know the standard armandhand signals. The leader gets the gunners attention and then points to the target. When the gunner returns the READY signal, the leader commands FIRE.

A.      Another way to designate obscure targets is to use easytorecognize reference points. All leaders and gunners must know terrain features and the terminology used to describe them see FM .,Map Reading and Land Navigation. When using a reference point, the word reference precedes its description. This is done to avoid confusion. The general direction to the reference point should be given.

A.   Gunners engage targets throughout their respective sectors. They must know how to effectively engage all s of targets, either inidually or with other gunners.

A.   The and nature of the enemy target determines how machine gun fire is applied. Automatic weapons fire in one of three rates rapid, sustained, or cyclic. The rates of fire for each machine gun are shown in Table A. The situation normally dictates the rate used, but the availability of ammunition and need for barrel changes play important roles as well. The rate of fire must be controlled to adequately cover the target, but not waste ammunition or destroy the barrel.

Check.While firing, the gunners periodically check with the leader for instructions.

Gun , shift fire, target or right/left sector.

Appendix I Improvised Explosive Devices, Suicide Bombers, and Unexploded Ordnance

AG is responsible for all action concerning the gun.

Table A. Example weapons squad fire commands and actions continued.

A.   Fire control includes all actions of the leader and Soldiers in planning, preparing, and applying fire on a target. The leader selects and designates targets. He also designates the midpoint and flanks or ends of a target, unless they are obvious to the gunner. The gunner fires at the instant desired. He then adjusts fire, regulates the rate of fire, shifts from one target to another, and ceases fire. When firing, the gunner should continue to fire until the target is neutralized or until signaled to do otherwise by the leader.

****Binoculars carried in the assault pack or in suile pouch on vest mission dependent.

Defense design should produce an equally balanced defense that is effective in all directions, unless a forced route of approach exists.

A.      This element prepares the gunners for further instructions. The leader may alert both gunners in the squad and may have only one fire, depending upon the situation. To alert and have both gunners fire, the leader announces FIRE MISSION. If he desires to alert both gunners but have only one fire, he announces GUN NUMBER ONE, FIRE MISSION. In all cases, upon receiving the alert, the gunners load their machine guns and place them on FIRE.

A.    The primary sector of fire is assigned to the gun team to cover the most likely avenue of enemy approach from all s of defensive positions.

GTL and his team will be tactically proficient and knowledgeable on this FM and applicable FMs and TMs that apply to the machine gun.

Fire.Gunners open fire without command on appropriate targets that appear within their sectors.

Figure A. MK , mm grenade machine gun, MOD .

C . All Rights Reserved.

A.      This element indicates the general direction to the target and may be given in one or a combination of the following methods.

Army Reserve Soldiers blow doors off urban ops training

M mm HEDP.This is the standard round for the MK and comes packed in either or round ammunition containers. It can penetrate inches of steel armor at zerodegree obliquity and inflict casualties out to meters from impact. It arms within to meters of the gun muzzle.

AG/GTL is always prepared to change the guns barrel spare barrel is always out when the gun is firing. Ensures the hot barrel is not placed on live ammunition or directly on the ground when it comes out of the gun.

n         If it clears the selected point, it is safe for the troops to advance to the selected point and to an unknown point beyond. If it is advantageous to have troops advance beyond the selected point, this rther point must be determined by testing new selected points until the line of aim and the selected point coincide. This point marks the line of safety.

A.   Once the enemy has been suppressed, machine gunners fire at the sustained rate. Sustained fire conserves ammunition and requires only infrequent barrel changes, but it might not be enough volume of fire to effectively suppress or destroy.

A.   DA Form R,Standard Range Card, provides a record of firing data and aids defensive fire planning.

Figure A. Example of ammunition requirement calculation.

A.      This element includes manipulation and rate of fire. Manipulation dictates the class of fire with respect to the weapon. It is announced as FIXED, TRAVERSE, SEARCH, or TRAVERSE AND SEARCH. Rate controls the volume of fire sustained, rapid, and cyclic. Normally, the gunner uses the sustained rate of fire. The rate of fire is omitted from the fire command. The method of fire for the machine gun is usually to round bursts M and to round bursts M/MB.

Classification of Fires With Respect to the Machine Gun

A.   A burst of fire is a number of successive rounds fired with the same elevation and point of aim when the trigger is held to the rear. The number of rounds in a burst can vary depending on the of fire employed.

If necessary for gunner to carry MB ammunition, carries it in on his back so the AG/GTL can access it without stopping the fire of the gun.

A.      Available MB machine gun ammunition is classified as follows Table A.

A.   Free gun fire is delivered against moving targets that must be rapidly engaged with st changes in both direction and elevation. Examples are aerial targets, vehicles, mounted troops, or inntry in relatively close formations moving rapidly toward or away from the gun position. When firing free gun, the weapon is normally fired at the cyclic rate of fire. Free gun fire consumes a lot of ammunition and does not have a beaten zone because each round seeks its own area of impact.

Appendix B ShoulderLaunched Munitions and Close Combat Missile Systems

Gunner echoes round count to ensure it is heard.

A.      Subsequent fire commands are used to make adjustments in direction and elevation, to change rates of fire after a fire mission is in progress, to interrupt fires, or to terminate the alert. If the gunner ils to properly engage a target, the leader must promptly correct him by announcing or signaling the desired changes. When these changes are given, the gunner makes the corrections and resumes firing without further command.

M/M .Caliber Tracer.Aids in observing fire. Secondary purposes are for incendiary effect and for signaling.

A.      Tracer ammunition is a quick and sure method of designating a target that is not clearly visible. When using this method, the leader should first give the general direction to direct the gunners attention to the target area. To prevent the loss of surprise when using tracer ammunition, the leader does not fire until he has given all elements of the fire command except the command to fire. The leader may fire his inidual weapon. The firing of the tracers then becomes the last element of the fire command, and it is the signal to open fire.

Gunner picks up gun and places into tripod. He gets AG/GTL to lock it in. Once locked in, the AG/GTL collapses bipod legs.

Without disturbing the lay of the gun, set the rear sight to , meters or the range to the target plus meters, whichever is the greater of the two ranges. Under no conditions should the sight setting be less than , meters.

A.      The weapons squad consists of a weapons squad leader and machine gun teams. Each machine gun team has a gunner, assistant gunner, and ammunition bearer. In some units the senior member of the gun team is the gunner. In other units the assistant gunner is the senior gun team member who also serves as the gun team leader. Table A illustrates equipment carried by the weapons squad. Table A illustrates the duty positions within the weapons squad and gives possible duty descriptions and responsibilities. The les serve to show possible position and equipment use only. Inidual unit SOPs and available equipment dictate the exact role each weapons squad member plays within his squad.

A.      The target description creates a picture of the target in the minds of the gunners. To properly apply their fire, the Soldiers must know the of target they are to engage. The leader should describe it briefly. If the target is obvious, no description is necessary.

When the target has width, direction is determined by aiming on one edge of the target area and noting the amount of traverse necessary to cover the entire target.

A.   Maximum ordinate is the highest point above the line of sight the trajectory reaches between the muzzle of the weapon and the base of the target. It always occurs at a point about twothirds of the distance from weapon to target and increases with range. Like trajectory, maximum ordinate increases as the range increases Figure A.

Table A. Example weapons squad duty positions and responsibilities.

A.      The leader sites the machine gun to cover the entire sector or to overlap sectors with the other machine guns. The engagement range may extend from over , meters where the enemy begins his assault to pointblank range. Machine gun targets include enemy automatic weapons and command and control elements.

Gun , traverse and search.Repeats command, searches objective for targets of opportunity within sector.Repeats command, searches objective for targets of opportunity in sector. Confirms target with AG/GTL before engaging.Gun , watch and shoot.

A.      The MB is organic to the Inntry platoon. Two machine guns and crews are found in the weapons squad Figure A. The MB can be fired in the assault mode in emergencies, but is normally fired from the bipod or tripod platform. It can also be vehicle mounted. The platoon leader through his weapons squad leader employs his MB machine guns with a rifle squad to provide long range, accurate, sustained fires against dismounted inntry, apertures in fortifications, buildings, and lightlyarmored vehicles. The MB also provides a high volume of shortrange fire in self defense against aircraft. Machine gunners use point, traversing, searching, or searching and traversing fire to kill or suppress targets.

A.      The primary requirement of a suile machine gun position in the defense is its effectiveness in accomplishing specific missions. The position should be accessible and afford cover and concealment. Machine guns are sited to protect the front, flanks, and rear of occupied portions of the defensive position, and to be mutually supporting. Attacking troops usually seek easilytraveled ground that provides cover from fire. Every machine gun should therefore have three positions primary, alternate, and supplementary. All of these positions should be chosen by the leader to ensure his sector is covered and that the machine guns are protected on their flanks.

Sector identified to AG/GTL once he identifies.

A.      A fire command is given to deliver effective fire on a target quickly and without confusion. When the leader decides to engage a target that is not obvious to the squad, he must provide them with the information they need to effectively engage the target. He must alert the Soldiers; give a target direction, description, and range; name the method of fire; and give the command to fire. There are initial fire commands and subsequent fire commands.

Protect motor movements, assembly areas, and supply trains in a bivouac.

Table A. Machine gun specifications continued.

meter above the ground. Grazing fire is employed in the final protective line FPL in defense and is only possible when the terrain is level or uniformly sloping. Any dead space encountered along the FPL must be covered by indirect fire, such as from an M. When firing over level or uniformly sloping terrain, the machine gun MB and M can attain a maximum of meters of grazing fire. The M can attain a maximum of meters. Paragraphs A and A discuss the FPL.

A.   The noise and confusion of battle may limit the use of some of these methods. Therefore, the leader must select a method or combination of methods that will accomplish the mission.

A.      Security includes all command measures to protect against surprise, observation, and annoyance by the enemy. The principal security measures against ground forces include employment of security patrols and detachments covering the front flanks and rear of the units most vulnerable areas. The composition and strength of these detachments depends on the of the main body, its mission, and the nature of the opposition expected. The presence of machine guns with security detachments augments their firepower to effectively delay, attack, and defend, by virtue of their inherent firepower.

A.      In the defense, the M adds increased firepower without the addition of manpower. Characteristically, Ms are light, fire rapidly, and have more ammunition than the rifles in the squad they support. Under certain circumstances, the platoon leader may designate the M machine gun as a platoon weapon.

A.   Flanking fire is delivered directly against the flank of the target. Flanking fire is highly desirable when engaging an enemy line formation. It then becomes enfilade fire as the beaten zone will coincide with the long axis of the target Figures A and A. Flanking fire against an enemy column formation is least desirable because the majority of the beaten zone normally lls before or after the enemy target.

A.      Leaders must calculate the number of rounds needed to support every machine gun throughout all phases of the operation. Ammunition must be allocated for each key event and to support movement with suppressive fires. For example, in the following list, key events are given for a platoon using two MBs in a supportbyfire position. Figure A illustrates steps the leader must take to accurately estimate the ammunition required.

A.      Where the area or zone of action is too wide to allow proper coverage by the platoons organic machine guns, the platoon can be assigned additional machine guns or personnel from within the company. This may permit the platoon to accomplish its assigned mission. The machine guns are assigned a zone or a sector to cover and they move with the maneuver element.

A.      Leaders must carefully plan for the rates of fire to be employed by machine guns as they relate to the mission and the amount of ammunition available. The weapons squad leader must fully understand the mission the amount of available ammunition and the application of machine gun fire needed to fully support all key events of the mission. Planning will ensure the guns do not run out of ammunition.

Neither the United States Army nor any other component of the Department of Defense has approved, endorsed, or authorized this website.

A.   SDZs were developed primarily for ranges and must be complied with when training, but they should also be complied with in combat when possible to minimize risk to friendly forces.

Gunner echoes command, also counts and fires when AG/GTL gives command to fire.

A.      There are distinct phases of rates of fire employed by the base of fire element

A.      In the offense the platoon leader has the option to eslish his base of fire element with one or two machine guns, the M light machine gun, or a combination of the weapons. The platoon sergeant or weapons squad leader may position this element and control its fires when the platoon scheme of maneuver is to conduct the assault with the Inntry squads. The MB machine gun, when placed on a tripod, provides sility and accuracy at greater ranges than the bipod, but it takes more time to maneuver the machine gun should the need arise. The machine gunners target key enemy weapons until the assault element masks their fires. They can also be used to suppress the enemys ability to return accurate fire, or to hamper the maneuver of the enemys assault element. They fix the enemy in position and isolate him by cutting off his avenues of reinforcement. They then shift their fires to the flank opposite the one being assaulted and continue to target any automatic weapons that provide enemy support, and engage any enemy counterattack. MB fires also can be used to cover the gap created between the forward element of the friendly assaulting force and terrain covered by indirect fires when the indirect fires are lifted and shifted. On signal, the machine gunners and the baseoffire element displace to join the assault element on the objective.

Repeats Gun Bipod and identifies location for gun.

M .mm Ball.For use against light materials and personnel, but not vehicles.

Ready.The gunner indicates that he is ready to fire by yelling UP or having the assistant gunner raise his hand above his head toward the leader.

Marks sector same as above.Echoes command to shift; identifies new target/sector. Adjusts gunner, alerts WSL once the gunner has shifted.Gunner echoes command, makes necessary adjustment, acquires new target. Confirms with AG/GTL that all is OK. Engages new sector when told.Echoes command with AG/GTL. Shift fire to TGT __.

A.   Gunners and automatic riflemen achieve oblique fire when the long axis of the beaten zone is at an angle other than a right angle to the front of the target Figures A and A.

Provide high volumes of fire into an engagement area EA.

A.    This technique is used with the bipod or tripod mount to mark sector limits and engage wide targets. It is good for all visibility conditions and is best suited for flat, level terrain. The gunner uses the following steps.

Machine guns used to defend march columns should be interspersed in the convoy, with emphasis on the lead and rear elements Figure A.

Table A. Example weapons squad fire commands and actions.

A.      The accomplishment of the platoons mission demands efficient and effective machine gun crews. Leaders consider the mission and organize machine guns to deliver firepower and fire support to any area or point needed to accomplish the assigned mission.

A.   The length of the beaten zone for any given range will vary according to the slope of the ground. On rising ground, the beaten zone becomes shorter but remains the same width. On ground that slopes away from the gun, the beaten zone becomes longer but remains the same width.

A.   Swinging traverse fire is employed against targets that require major changes in direction but little or no change in elevation. Targets may be dense, wide, in close formations moving slowly toward or away from the gun, or vehicles or mounted troops moving across the front. If tripod mounted, the traversing slide lock lever is loosened enough to permit the gunner to swing the gun laterally. When firing swinging traverse, the weapon is normally fired at the cyclic rate of fire. Swinging traverse consumes a lot of ammunition and does not have a beaten zone because each round seeks its own area of impact.

A.   Gunners targets in combat are normally enemy troops in various formations or displacements, which require distribution and concentration of fire. These targets often have both width and depth, and the application of machine gun fire is designed to completely cover the area in which the enemy is known or suspected to be. These targets may be easy to see or may be indistinct and difficult to locate. The of the target, stated in terms of the number of aiming points required to engage it completely, determines its .

A.   Using a tripodmounted machine gun, the gunner places a log or board beneath the barrel, positioning it so the barrel, when resting on the log or board, is at the proper elevation to obtain grazing fire. When appropriate, he marks the sector limits as described for the bipod in the preceding paragraph. This technique is used only if a TE mechanism is not available.

A.   As the range to the target increases, the beaten zone becomes shorter and wider. Conversely, as the range to the target decreases, the beaten zone becomes longer and narrower Table A.

Concentrate fires where they want to kill the enemy.

A.   When the range to the target is greater than meters, overhead fire should be delivered only in an emergency. Even then, fire should only extend to a range at which the tracers or strike of the bullets can be seen by the gunner. In this situation the leaders rule applies Figure A. The platoon or section leader uses the leaders rule only when the target is greater than meters. The rule follows

M .mm Tracer.Generally used for adjustments after observation, incendiary effects, and signaling. When tracer rounds are fired, they are normally mixed with ball ammunition in a ratio of four ball rounds to one tracer round.

Gun barrel change.Fires one more burst.

Lay the gun on the target with the correct sight setting to hit the target.

.   Fires with respect to the target include enfilade, frontal, flanking, and oblique fire Figures A,

Figure A. Application of leaders rule.

M .mm Tracer.M tracer ammunition can be fired with the M, but accuracy is degraded. It should therefore only be used in emergency situations when M ammunition is not available.

The AB is the rifleman/equipment bearer for the gun team.

A.   When using the range card method of fire control, the leader must ensure all range cards are current and accurate. Once this is accomplished, the leader may designate certain targets for certain weapons with the use of limiting stakes or with fire commands. He should also designate nofire zones or restricted fire areas to others. The key ctor in this method of fire control is that gunners must be well disciplined and pay attention to detail.

A.   Fixed fire is delivered against a stationary point target when the depth and width of the beaten zone will cover the target with little or no manipulation needed. After the initial burst, the gunners will follow any change or movement of the target without command.

Repeats AG/GTL command. Once done, Gun up.

If need to know round count, prompt Gun , round count.

Increased rate as the assault nears the objective.

GTL assists the WSL on the best way to employ the MB.

A, and A. These targets are normally presented to gun teams by the enemy and must be engaged as they are presented. For instance, if the enemy presents its flank to the gun crew as it moves past their position from the left or right, the gun crew will have no choice but to employ flanking fire on the enemy.

A.   Defilade positions protect gunners from frontal or enfilading fires Figure A. Cover and concealment may not provide the gunner a view of some or all of the target area. In this instance, some other member of the platoon must observe the impact of the rounds and communicate adjustments to the gunner Figure A. Gunners and leaders must consider the complexity of laying on the target. They must also take into account the gunners inability to make rapid adjustments to engage moving targets, the ease with which targets are masked, and the difficulty in achieving grazing fires for an FPL.

A.   SOPs are actions to be executed without command that are developed during the training of the squads. Their use eliminates many commands and simplifies the leaders fire control. SOPs for certain actions and commands can be developed to make gunners more effective. Some examples follow

AG/GTL is a team leader with the responsibilities of a fire team leader.

Commence Firing or Change Rate of Firing.The leader brings his hand palm down to the front of his body about waist level, and moves it horizontally in front of his body. To signal an increase in the rate of fire, he increases the speed of the hand movement. To signal slower fire, he decreases the speed of the hand movement.

Always carries the necessary tools for the gun to be properly cleaned, along with a sufficient amount of oil for the guns proper function.

A.   Enfilade fire occurs when the long axis of the beaten zone coincides or nearly coincides with the long axis of the target. It can be frontal fire on an enemy column formation or flanking fire on an enemy line formation.This is the most desirable class of fire with respect to the target because it makes maximum use of the beaten zone.Leaders and gunners should always strive to position the guns to the extent possible that they can engage enemy targets with enfilade fire Figures A and A.

A.   Leaders and gunners should strive at all times to position their gun teams where they can best take advantage of the machine guns beaten zone with respect to an enemy target. Channeling the enemy by use of terrain or obstacles so they approach a friendly machine gun position from the front in a column formation is one example. In this situation, the machine gun would employ enfilade fire on the enemy column, and the effects of the machine guns beaten zone would be much greater than if it engaged that same enemy column from the flank.

Other Signals.The leader can devise other signals to control his weapons. A detailed description of armandhand signals is given in FM .

A.   Techniques of fire include assault fire; overhead fire; and fire from a defilade position. Only automatic rifles use assault fire.

A.      All vocal commands from the leaders to change the rates of fire are accompanied simultaneously by handandarm signals.

A.      Machine guns in the SBF role should be set in and assigned a primary and alternate sector of fire as well as a primary and alternate position.

Defend against hovering rotary aircraft.

A.      Available M ammunition is classified as follows Table A.

M .Caliber Ball.For use against enemy personnel and light material targets.

Initial heavy volume rapid rate to gain fire superiority.

WSL changes gun teams sector of fire or shift fire

M .mm Tracer.For observation of fire, incendiary effects, signaling, and for training. When tracer rounds are fired, they are normally mixed with ball ammunition in a ratio of four ball rounds to one tracer round.

Repeats rate of fire command, keeps own count. Fires when told to fire. Adjusts rate of fire off of lead gun.

Lift fire, lift fire, lift fire. Or

When the gun is firing, AG/GTL spots rounds and makes corrections to the gunners fire. Also watches for friendly troops to the flanks of the target area or between the gun and the target.

Follows the gunner without hesitation. During movement moves to the right side of the gunner and no more than one meters rush away from the gun.

NOTESoldiers must be aware that with the night vision device, temporary blindness white out may occur when firing tracer ammunition at night or when exposed to other external light sources. Lens covers may reduce this effect.

***Spare barrels marked by relative age with ¼ pieces of green tape on carrying handle.

A.      When the leader makes an error in the initial fire command, he corrects it by announcing CORRECTION, and then gives the corrected element. When the leader makes an error in the subsequent fire command, he may correct it by announcing CORRECTION. He then repeats the entire subsequent fire command.

A.   Automatic weapons achieve grazing fire when the center of the cone of fire does not rise more than

A.      The machine gun delivers an accurate, highvolume rate of lethal fire on irly large areas in a brief time. When accurately placed on the enemy position, machine gun fires secure the essential element of fire superiority for the duration of the firing. Troops advancing in the attack should take full advantage of this period to maneuver to a vorable position from where they can cilitate the last push against the enemy. In addition to creating enemy casualties, machine gun fire destroys the enemys confidence and neutralizes his ability to successfully engage the friendly maneuver element.

To interrupt firing, the leader announces CEASE FIRE, or he signals to cease fire. The gunners remain on the alert. They resume firing when given the command FIRE.

Gunner makes necessary adjustments, tells AG/GTL whether he identifies or not. Engages or makes further adjustments.

Echoes rate of fire Sustained __ seconds.

GTL assists the WSL in all areas. He advises him of any problems either tactical or administrative.

Change Direction or Elevation.The leader extends his arm and hand in the new direction and indicates the amount of change necessary by the number of fingers extended. The fingers must be spread so the gunner can easily see the number of fingers extended. Each finger indicates meter of change for the weapon. If the desired change is more than meters, the leader extends his hand the number of times necessary to indicate the total amount of change. For example,right ninewould be indicated by extending the hand once with five fingers showing and a second time with four fingers showing for a total of nine fingers.

Appendix D Vehicle Employment Considerations

This entry was posted in simple machine and tagged . Bookmark the permalink.

Comments are closed.